2.8inch Arduino Display

The printable version is no longer supported and may have rendering errors. Please update your browser bookmarks and please use the default browser print function instead.

语言选择 Languages
➤中文
➤EN

Product Video

Related Video

Product Picture

Product Description

Supports development boards such as Arduino UNO and Mega2560 for plug-in use without wiring
320X240 resolution, clear display, support for touch function
Support 16-bit RGB 65K color display, display rich colors
8-bit parallel bus, faster than serial SPI refresh
On-board 5V/3.3V level shifting IC, compatible with 5V/3.3V operating voltage
Easy to expand the experiment with SD card slot
Provides an Arduino library with a rich sample program
Military-grade process standards, long-term stable work
Provide underlying driver technical support

Product Parameters

Name	Parameter
Display Color	RGB 65K color
SKU	MAR2808
Screen Size	2.8(inch)
Type	TFT
Driver IC	ILI9341
Resolution	320*240 (Pixel)
Module Interface	8-bit parallel interface
Active Area	43.2*57.6(mm)
Module PCB Size	52.70*78.22(mm)
Operating Temperature	-20℃~60℃
Storage Temperature	-30℃~70℃
Operating Voltage	5V/3.3V
Power Consumption	About 90mw
Product Weight	44(g)

Interface Definition

Number	Pin Label	Pin Description
1	LCD_RST	LCD bus reset signal, low level reset
2	LCD_CS	LCD bus chip select signal, low level enable
3	LCD_RS	LCD bus command / data selection signal, low level: command, high level: data
4	LCD_WR	LCD bus write signal
5	LCD_RD	LCD bus read signal
6	GND	Power ground
7	5V	5V power input
8	3V3	3.3V power input, this pin can be disconnected
9	LCD_D0	LCD 8-bit data Bit0
10	LCD_D1	LCD 8-bit data Bit1
11	LCD_D2	LCD 8-bit data Bit2
12	LCD_D3	LCD 8-bit data Bit3
13	LCD_D4	LCD 8-bit data Bit4
14	LCD_D5	LCD 8-bit data Bit5
15	LCD_D6	LCD 8-bit data Bit6
16	LCD_D7	LCD 8-bit data Bit7
17	SD_SS	SD card SPI bus chip select signal, low level enable
18	SD_DI	SD card SPI bus MOSI signal
19	SD_DO	SD card SPI bus MISO signal
20	SD_SCK	SD card SPI bus clock signal

Connect to Arduino


Arduino UNO direct insertion picture	Arduino Mega2560 direct insertion picture

How to use on Arduino

Step 1: Download the test program

Download the Arduino test program from the Program Download column
For a description of the relevant test procedures, please refer to the test program documentation in the package

Step 2: Connect the Arduino development board

Plug the module directly into the Arduino development board ( Do not plug in?)
After the module is plugged in, power on the Arduino board

Step 3: Copy the dependent library

Make sure the Arduino IDE is installed on your computer (if it is not installed: Arduino IDE download URL)
After installing the Arduino IDE, you need to copy the dependent library to the Arduino project directory as follows:

(1) Decompress the downloaded test package

(2) Copy the dependent libraries in the Install libraries directory in the package (shown below) to the libraries folder

of the Arduino project directory （ Don't know the Arduino project directory?）

Step 4: Compile and download the program to the development board

Open the sample in the Example directory of the package to test, compile and download（ Don't know how to compile and download?）

Step 5: Observe the running of the program

After the program is downloaded, run it directly and observe the running status. If it can be displayed normally, the program runs

successfully, as shown in the following figure (take the display_graphics program as an example):