10.1-DSI-C 1024600

Product Introduction

Product Images

Product Features

• 10.1-inch DSI touchscreen with 5-point capacitive touch control
• IPS display panel with a hardware resolution of 1024×600
• Full lamination technology for clearer image quality
• Tempered glass touch cover with a hardness rating of up to 6H
• LCD driven via DSI interface, supporting refresh rates of up to 60Hz
• Backlight brightness can be adjusted through software
• Metal back cover with a passive cooling design

---

Product Specifications

• Size: 10.1(inch)
• SKU: DSI1061
• Resolution: 1024x600(dots)
• Backlight Brightness: 210cd/m2
• Touch: 5-point capacitive touch
• Touchscreen Dimensions: 236.00*145.57(mm)
• Active Area (AA): 222.72*125.28(mm)
• Package Dimensions:
• Weight (Including Package):
• Power Consumption:

---

DSI-22PIN Interface Definition

---

Hardware Connection

Working with Pi 4B/3B+/3A+/3B/2B/B+/A+

1. Connect the 10.1inch DSI LCD to the 15PIN DSI1 interface on the Raspberry Pi board using the DSI-Cable-12cm cable.
2. Connect the LCD power interface to the 5V and GND pins on the Raspberry Pi board using the 2PIN power cable.
3. For convenient use, the Raspberry Pi 4 can be mounted onto the back of the 10.1inch DSI LCD using screws, with the brass standoffs installed as shown below:

Working with Pi 5/CM4/CM3+/CM3

1. Connect the 10.1inch DSI LCD to the 22PIN DSI1 interface on the Raspberry Pi board using the DSI-Cable-12cm cable.
2. Connect the LCD power interface to the 40PIN GPIO header on the Raspberry Pi using the 2PIN power cable.
3. For convenient use, the Raspberry Pi 5 can be mounted onto the back of the 10.1inch DSI LCD using screws, with the brass standoffs installed as shown below:

---

Software Configuration

Method 1: Flash the Latest Official Image Using Raspberry Pi Imager

Compatible with Raspberry Pi OS, Ubuntu, Kali, Volumio, and RetroPie systems for Raspberry Pi.

• 1. Connect the TF card to your PC, download and use Raspberry Pi Imager to flash the corresponding system image.

• 2. After flashing the image, log in to the Raspberry Pi system and access the user command line (Default username: pi; password: raspberry).
• Obtain the latest driver from GitHub (the Raspberry Pi must be connected to the Internet).
• Enter the following commands to install the driver.

sudo rm -rf DSI-1024x600
git clone https://github.com/goodtft/DSI-1024x600.git
chmod -R 755 DSI-1024x600
cd DSI-1024x600/
sudo ./DSI-1024x600-show

• The default driver uses I2C0.
• To use DSI0 + I2C1, run the following command:

sudo ./DSI-1024x600-show i2c1 dsi0

Adjusting Backlight Brightness

• 1. Click the menu in the upper-left corner, navigate to Preferences → Control Center, and select Screens.
  

• 2. Navigate to "Screen"->"DSI-1"->"Brightness", select the desired backlight brightness, and click "Apply" to complete the brightness configuration.

You can also use the graphical backlight adjustment tool provided by us. (This program is only compatible with Bookworm and Bullseye systems.) Enter the following commands in the terminal to download, install, and use the tool:

wget http://www.lcdwiki.com/res/software/lcd-dsi-brightness-go.zip
unzip lcd-dsi-brightness-go.zip
chmod -R 755 lcd-dsi-brightness-go
cd lcd-dsi-brightness-go
sudo ./install.sh

After installation, you can launch the program from Start Menu -> Accessories -> Brightness, as shown below:

Alternatively, you can enter the following commands in the terminal to control the backlight brightness:

echo X | sudo tee /sys/class/backlight/*/brightness

Here, X represents any integer from 0 to 255. 0 indicates the lowest backlight brightness, while 255 indicates the highest backlight brightness. For example:

echo 100 | sudo tee /sys/class/backlight/*/brightness
echo 0 | sudo tee /sys/class/backlight/*/brightness
echo 255 | sudo tee /sys/class/backlight/*/brightness

Display Rotation

Display Rotation on Bookworm

Rotate via GUI

• 1. Open the "Screen Configuration" application.
  

• 2. Navigate to "Screen"->"DSI-1"->"Touchscreen" and select "10-005d Goodix Capacitive TouchScreen".

• 3. Click "Apply" and close the current window. Follow the prompt to restart the system. The touchscreen selection process will then be complete.

• 4. Navigate to "Screen"->"DSI-1"->"Orientation", select the desired rotation direction, and click "Apply" to synchronize the rotation of the display and touchscreen.

Note: The above synchronized rotation method is only supported on Bookworm. For Bullseye and Butser systems, touchscreen rotation must be configured separately after rotating the display.

Touch Mode Selection

Trixie and Bookworm systems support two touch modes, which can be switched in the Screen Configuration > Touchscreen menu:

• 1. Mouse Emulation (Default)

Single tap = Left mouse button function
Long press = Right mouse button function
Double-click supported
Page scrolling and multi-touch gestures are not supported

Note: This mode is suitable for scenarios requiring mouse-like operations, such as double-clicking to open File Manager and long-pressing to trigger the right-click function.

• 2. Multitouch

Supports multi-touch functionality
Supports page scrolling
Double-click and right-click via long press are not supported

Note: This mode is suitable for touch-optimized applications, such as web browsing and scrolling through lists.

---

Resources

10.1inch_IPS_Display_Datasheet

10.1inch_IPS_Display_User_Manual

10.1inch_IPS_Display_Dimensional_Drawing