Difference between revisions of "3.2inch RPi Display"
(→Driver Installation) |
(→Step 2: Burn the system image) |
||
Line 135: | Line 135: | ||
https://www.raspberrypi.org/downloads/raspbian/ | https://www.raspberrypi.org/downloads/raspbian/ | ||
===Step 2: Burn the system image=== | ===Step 2: Burn the system image=== | ||
− | If you don't know how to do that,you can refer to the [https://www.raspberrypi.org/documentation/installation/installing-images/README.md Raspberry Pi office tutorial] | + | If you don't know how to do that, you can refer to the [https://www.raspberrypi.org/documentation/installation/installing-images/README.md Raspberry Pi office tutorial] |
===Step 3: Open terminal(SSH) and install the driver on RaspberryPi=== | ===Step 3: Open terminal(SSH) and install the driver on RaspberryPi=== |
Revision as of 16:28, 3 September 2018
Contents
Product pictures
Features
- 320×240 resolution
- Resistive touch control
- Supports any revision of Raspberry Pi (directly-pluggable)
- Compatible with Raspberry Pi A, B, A+, B+, 2B, 3B, 3B+versions
- Drivers provided (works with your own Raspbian/Ubuntu directly)
- Size perfectly fits the Raspberry Pi
- High quality immersion gold surface plating
- Supports Raspbian system, Ubuntu system ,Kali Linux system
Key Parameters
SKU | MPI3201 |
LCD Type | TFT |
LCD Interface | SPI |
Touch Screen Type | Resistive |
Touch Screen Controller | XPT2046 |
Colors | 65536 |
Backlight | LED |
Resolution | 320*240 (Pixel) |
Aspect Ratio | 8:5 |
Active Area | 48.6*64.8(mm) |
Dimensions | 84.91*56.54(mm) |
Weight | 120(g) |
Interface
PIN NO. | SYMBOL | DESCRIPTION |
---|---|---|
1, 17 | 3.3V | Power positive (3.3V power input) |
2, 4 | 5V | Power positive (5V power input) |
3, 5, 7, 8, 10, 22 | NC | NC |
6, 9, 14, 20, 25 | GND | Ground |
11 | TP_IRQ | Touch Panel interrupt, low level while the Touch Panel detects touching |
12 | KEY1 | Key |
13 | RST | Reset |
15 | LCD_RS | LCD instruction control, Instruction/Data Register selection |
16 | KEY2 | KEY |
18 | KEY3 | KEY |
19 | LCD_SI / TP_SI | SPI data input of LCD/Touch Panel |
21 | TP_SO | SPI data output of Touch Panel |
23 | LCD_SCK / TP_SCK | SPI clock of LCD/Touch Panel |
24 | LCD_CS | LCD chip selection, low active |
26 | TP_CS | Touch Panel chip selection, low active |
Driver Installation
This LCD Module need install driver first.
Step 1:Download the Raspbian IMG
https://www.raspberrypi.org/downloads/raspbian/
Step 2: Burn the system image
If you don't know how to do that, you can refer to the Raspberry Pi office tutorial
Step 3: Open terminal(SSH) and install the driver on RaspberryPi
(tested on Raspberry Pi 3B+,3B,2B,2B+,1B,ZERO)
Run:
sudo rm -rf LCD-show git clone https://github.com/goodtft/LCD-show.git chmod -R 755 LCD-show cd LCD-show/ sudo ./LCD32-show
Wait A Few Minutes, when the system reboot ok, you can see that.
Download Resources
- Document
- How_to_install_the_LCD_driver_V1.2
- How_to_install_matchbox-keyboard
- How_to_calibrate_the_resistance_touch_screen-V1.2
- How_to_change_display_direction-GPIO-Resistive_Touch-V1.2
- Driver download
- download:LCD-show.tar.gz
- Images download
- If you have difficulty installing the driver, or if you still can't use the display properly after installing the driver,
- Please Try our Configned images for tested.
- Just need download and write the image into the TF card. DO NOT need any driver installation steps.
Image Name | Version | Support | Password | Download | |
---|---|---|---|---|---|
Raspbian | 2018-06-29 | PI3B+/A/A+/B/B+/PI2/
PI3/ZERO/ZERO W |
user:pi
password:raspberry |
(addr1)Baidu Pan: | 3.2inch-Raspbian-20180629.7z |
(addr2)Mega: | |||||
Ubuntu | Mate:16.04 | PI3,PI2 | user:pi
password:raspberry |
(addr1)Baidu Pan: | |
(addr2)Mega: | |||||
Kali-linux | 2018.2(nexmon) | PI3B+,PI3,PI2 | user:root
password:toor |
(addr1)Baidu Pan: | |
(addr2)Mega: |
- Software