2.4inch 16BIT Module ILI9341 SKU:MRB2408

From LCD wiki
Jump to: navigation, search
语言选择(Other languages): 中文 English

Product Picture

MRB2408-002.jpg MRB2408-004.jpg

Product Description

  • 2.4-inch color screen, support 16BIT RGB 65K color display, display rich colors
  • 240x320 resolution for clear display
  • Support 8-bit/16-bit parallel bus switching (the default is 16-bit), fast transfer speed
  • Supports ALIENTEK STM32 Mini, Elite, WarShip, Explorer, and Apollo development boards for direct plug-in use
  • Support for touch function
  • Support SD card function expansion
  • Provides a rich sample program for STM32 and C51 platforms
  • Military-grade process standards, long-term stable work
  • Provide underlying driver technical support

Product Parameters

Name Parameter
Display Color 16BIT RGB 65K color
Screen Size  2.4(inch)
Screen Type TFT
Driver IC ILI9341
Resolution 320*240 (Pixel)
Module Interface 8Bit or 16Bit parallel interface
Active Area  48.96*36.72(mm)
Touch Screen Type resistive touch screen
Touch IC XPT2046
Module PCB Size 44.25x76.00 (mm)
Operating Temperature -20℃~60℃
Storage Temperature -30℃~70℃
Operating Voltage 3.3V/5V
Power Consumption TBD
Rough Weight(Package containing) 35 (g)

Interface Definition


The red box in the above figure is the 8-bit/16-bit data bus mode switch, which is described as follows:

Solder R1 with 0Ω resistor or short circuit directly, and disconnect R2: select 16-bit data bus mode (default), use D1~D8, D10~D17 data pins
Solder R2 with 0Ω resistor or short circuit directly, and disconnect R1: select 8-bit data bus mode, use D10~D17 data pins
Number Pin Label Description
1 CS LCD reset control pin( low level enable)
2 RS LCD register / data selection control pin(high level: register, low level: data)
3 WR LCD write control pin
4 RD LCD read control pin 
5 RST LCD reset control pin( low level reset)
6 D1 LCD data bus low 8-bit pin(When 8-bit parallel data bus mode is selected, the lower 8-bit data pins are not used)
7 D2
8 D3
9 D4
10 D5
11 D6
12 D7
13 D8
14 D10 LCD data bus high 8-bit pin
15 D11
16 D12
17 D13
18 D14
19 D15
20 D16
21 D17
22 SCS SD card selection control pin (used when using the SD card expansion function, this test program is not used)
23 BL LCD backlight control pin(High level light)
24 VDD Module power positive pin (module has integrated voltage regulator IC, so the power supply can be connected to 5V or 3.3V)
25 VDD
26 GND Module power ground pin
27 GND
28 V5 LCD backlight power positive pin (default shared onboard backlight power supply, this pin can not be connected)
29 MO Touch screen SPI bus data input pin
30 MI Touch screen SPI bus data output pin
31 PEN Touch screen interrupt detection pin(Low level when a touch occurs)
32 FCS Flash chip select control pin (used when using the Flash extension function, this test program is not used)
33 TCS Touch screen IC chip select control pin(Low level enable)
34 CLK Touch screen SPI bus clock control pin

How to use on STM32 development board

This module is compatible with the ALIENTEK STM32 development board. The specific usage is as follows:

  • Step 1: Download the test program
  1. Download the STM32 test program from the Program Download column
  2. For a description of the relevant test procedures, please refer to the test program documentation in the package
  • Step 2: Connect the STM32 development board
  1. Find the TFTLCD Slot on the development board, connect the module pins and Slot(For example, the module CS pin corresponds to the slot CS pin),
and then plug them directly into the Slot
  • Step 3: Compile and download the program to the development board
  1. Compile and download the program you need to test to the STM32 development board( Don't know how to compile and download?
  • Step 4: Observe the running of the program
  1. After the program is finished, observe the running status of the program. If it can be displayed normally, the program runs successfully.

Program Download

Product Documentation

Reference Materials

Common Software